5393 Farrell Rd. Sanford, NC 27330

Salter Brecknell Counting Scales for Sale B130 Weighing Systems

Call (919) 776-7737

Celebrating over 30 years in business

PRODUCTS

Central Carolina Scale sells and services Low Profile Floor Scales and Weighing Equipment in the Central Carolina Scale Electronic Catalog

SALTER BRECKNELL B130 COUNTING SCALE

The B130 is a 30,000 displayed resolution counting scale with a robust plastic housing 300 mm (11.8") wide x 305 mm (12") long and 110 mm (4.3") high. It has a level bubble with four adjustable feet to assure levelness. The B130 is also equipped with a removable stainless steel platter 292 mm wide (11.5") x 222 mm (8.75") long and 13 mm (0.5") high. The B130 has three 6 digit 14.2 mm (0.56") easy to read LED displays and a rechargeable lead acid battery with a run time of 20 hours of continuous use between charges and comes standard with wall mount power supply.

General Counting Information
If there is no piece weight, the scale will not go into count mode. Once a piece weight is established, it remains active until another piece weight is automatically calculated by a sampling process. After counting items, remove them and the display should return to zero. If not, press the ZERO key. A counting scale needs a minimum amount of weight to calculate counts with accuracy. Salter Brecknell recommends the sample weight be a minimum of 0.1% of scale capacity. The sample weight is the total weight of your sample items. The table below shows the minimum sample weights recommended to guarantee the most accurate counts.

Minimum Total Sample Weight Recommended For Accurate Counting
Scale Capacity	Pounds	Grams
(B130-12) 6 kg / 12 lb	0.02	6
(B130-30) 15 kg / 30 lb	0.05	15
(B130-60) 30 kg / 60 lb	0.1	30

B130 Features
Tare
Unit Switching
Upper & Lower Target
Accumulation
Piece Weight entry of a known average piece weight.

B130 Benefits
Accuracy - Within ±3 divisions @ full load
High Performance - 30,000 divisions
Power - AC adapter with rechargeable battery @ 20 hours battery life between charges
Construction - Rugged ABS plastic base, stainless steel weight platter

Counting by Sampling

Follow these steps to count items using the sampling method. For count accuracy all items should be uniform in weight. Errors in count will occur if parts vary in weight.

1. Turn the scale on and zero the display, if necessary, using the Zero key. Be sure the scale is displaying weight in your preferred unit of measure. Change it using the Units key, if necessary.

2. Place a known number of objects on the scale. This is the sample weight the scale will use to calculate a piece weight… Weight of the items is displayed in the WEIGHT window.

3. Key in the number of objects you placed on the scale…SPL.PCS is displayed in the PIECE WEIGHT window and the number you keyed in is displayed in the COUNT window.

4. Press the Enter key to accept the keyed in number. (If you make an error in keying in the number, press the Clear key to clear the count in the COUNT window and re-key the correct number.)… The scale calculates the weight of each piece (the piece weight) and
displays the count in the COUNT window.

5. Place the items to be counted on the scale… The total weight, piece weight and count of the items will be shown in the three display windows respectively.

6. Remove the items from the scale and repeat steps 5 and 6 to count items of the same piece weight.

7. Repeat steps 1-6 to count items of a different piece weight.

Note: Piece weight is displayed in grams/decimal grams or LB/decimal pounds.

Note: The original piece weight will be held in memory until a new piece weight has been determined. Turn the scale off, then on to return to normal weighing mode.

Accumulating Counts

The B130 brecknell counting scale can accumulate the counts from different weighments into a total value stored in memory. Follow these steps to perform accumulations.

1. Follow the different counting methods described in Scale Operation on page 5 of the manual to count items placed on the scale.

2. When the count is displayed, press the Accu+ key to accumulate the count to memory…
The count is added into memory, and temporarily, Add is displayed in the WEIGHT window, the number of accumulations is displayed in the PIECE WEIGHT window and the accumulated count is shown in the COUNT window. The display automatically returns to the normal counting mode.

3. Remove the items, allow the scale to return to zero weight and count, and repeat the process of putting items on the scale and pressing the Accu+ key to accumulate the counts…
The total of accumulated counts is shown in the COUNT window.

4. To clear the accumulator, press Accu+ key, then the Clear key while the accumulated data is displayed… Memory is cleared of the accumulated data and the scale returns to normal counting mode. Note: To view the accumulator data, remove all weight from the scale and
press Accu+. The data is temporarily displayed before returning to count mode.

5. The scale will not accumulate more than 999,999 times, or show an accumulated quantity over 16,777,215. If this occurs the display will show ------. This means over range. When the accumulated quantity is more than the six digit display can show (999999), it will be displayed by alternately flashing the first four digits H XXXX) then the second four digits (L XXXX). The H stands for High order numbers and the L for low order numbers. For example: When the accumulated quantity is 12,345,678, the COUNT window will alternately flash H 1234 and L 5678.

Note: Remove the counted items from the scale and let the scale return to stable condition before you can count more items and perform a successful accumulation again.

Part Number	Capacity
816965004737	6 kg x 0.2 g / 12 lb x 0.0005 lb
816965004690	15 kg x 0.5 g / 30 lb x 0.001 lb
816965004706	30 kg x 1 g / 60 x 0.002 lb